You are here

Percepio Tracealyzer - a PSoC DMA Streamport | 赛普拉斯半导体

Percepio Tracealyzer - a PSoC DMA Streamport

[re-printed from https://iotexpert.com]

In the last Article I analyzed the performance problems of my firmware based PSoC Tracealyzer Streamport … which was terrible.  Although it has been a long time since I used the PSoC4M DMA engine, I knew that it would solve my problem.  In this article I'll show how to use the PSoC DMA, then Ill build and analyze a PSoC DMA Streamport for Tracealyzer.

PSoC4 UART DMA

The DMA block that shows up in the PSoC4200M, PSoC 4200L and PSoC 4 BLE is pretty amazing.  It can do a bunch of stuff.  Here is a snapshot that I took out of the TRM.  This block sits on the main AHB bus inside of the PSoC.  It can act as a master (see the block that says Master I/F) and read and write any of things in the Arm address space including the Flash, SRAM, and all of the peripherals.  It has an incoming trigger which can get the transfers going and when it is done it can trigger an interrupt or another DMA channel.  The Slave I/F allows the CPU to program the block.  The device has 8-channels with each channel having 2 descriptors (so it can ping pong).

PSoC 4 DMA

 

Before I tried to make the PSoC DMA Streamport I started by looking at the example projects by pressing “File->Code Example”

CY3295 Kit Image

 

Then filtering for DMA

CY3295 Kit Image

 

Finally creating project.  This project uses two DMA channels, one for the UART receive and one for the UART Transfer.  It lets you type characters into the UART, it saves them in one of the RAM buffers, then when you have typed 8, it DMAs them back into the Transmit channel of the UART.  This example ping-pings back and forth between two RAM buffers.

CY3295 Kit Image

 

I decided that it would be best to build a bare metal DMA project called “test-uart” to prove that I understood.  This project will DMA transfer an array of characters to the UART when the user presses the switch on the board or a “s” on the keyboard.  The first thing to do is build the schematic with a UART, a DMA block,  two output pins, and input pin and an interrupt.

CY3295 Kit Image

Place an SCB UART, then configure it (change the name, but accept all of the defaults)

CY3295 Kit Image

 

Then click on the advanced tab.  Turn on the DMA for Transfer (TX Output) and set the “FIFO Level” to 7.  This will cause the UART to assert DMA signal anytime the transmit FIFO has less than 7 bytes.  In  other words … FEED ME!!!

CY3295 Kit Image

 

After configuring the UART, Set the PINs

CY3295 Kit Image

 

Next configure the DMA.  The memory array that I have will be “uint8_t” aka “char”.  So the input needs to be “bytes”.  The UART FIFO hold Words… aka 4 bytes.  So I need to configure the transfers to do “Byte to Word”.  After the DMA transfer is done, I setup the DMA to create an interrupt (so that I can reset everything in the CPU) and to invalidate the descriptor.

CY3295 Kit Image

In the firmware works by

  • Turning on the UART
  • Enabling the DMA
  • Setting up the channel with the address of the buffer that I am going to write to (aka the TX FIFO) and asking for an interrupt

Then looping:

  • When the User presses “s” or the switch, I set myFlag to be 1.
  • If it is 1 and the channel is inactive, then initialize the “source” address, setup the number of transfer elements to be the number in my array, validate the descriptor, and turn on the channel.

When the channel turns on, the Tx fifo will be empty so it will assert the Tx Out, which will make the DMA keep triggering and copying 1 byte at a time into the FIFO.  While this is happening, the UART will try to empty the fifo by sending the bytes.  Finally when the DMA reaches the end of the RAM buffer, it will stop, and at some point the TX FIFO will finish emptying.  The DMA will trigger the interrupt to toggle the BLUE LED.  And the whole process can start again.

#include "project.h"
#include <stdio.h>
 
// A flag to trigger the DMA
volatile int myFlag=0;
  
static const char myArray[]="asdf1234asdfadsfasdfadsfqwerasdfqwerqwer9\n";
 
CY_ISR(sw_handler)
{
    myFlag = 1;
    SW_ClearInterrupt();
}
 
// This is called TWICE at the end of the DMA transaction
CY_ISR(myDMA)
{
    BLUE_Write(~BLUE_Read());
}
int main(void)
{
    CyIntEnable(CYDMA_INTR_NUMBER);
    CyGlobalIntEnable; /* Enable global interrupts. */
 
    char c;
    
    UART_Start();
    UART_UartPutString("Started\n");
  
    isr_1_StartEx(sw_handler);
  
    CyDmaEnable();
    
    DMA_Init();
    DMA_SetDstAddress(0, (void *)UART_TX_FIFO_WR_PTR);
    DMA_SetInterruptCallback(myDMA);
 
    while(1)
    {
        c = UART_UartGetChar();
        switch(c)
        {      
            case 's':
                myFlag = 1;
            break;
        }
        
        // This turns on the DMA so that the string will go to the UART.
        if(myFlag && CyDmaGetActiveChannels() == 0)
        {
            DMA_SetSrcAddress(0, (void *)myArray);
            DMA_SetNumDataElements(0,strlen(myArray)-1);
            DMA_ValidateDescriptor(0);
            DMA_ChEnable();
            myFlag=0;
        }
    }
}

PSoC DMA Streamport

Now that I understand how to use the DMA, I can create the PSoC DMA Streamport by copying the project “1-BlionkingLED_UART_TRACE” project and calling it “1-BlinkingLED_UART_TRCE_DMA”.  Next, add the DMA and modify the UART.

CY3295 Kit Image

 

Configure the UART

CY3295 Kit Image

 

Turn on the UART DMA and set the level to 7

CY3295 Kit Image

 

Configure the DMA Block

CY3295 Kit Image

 

Make byte transfers and byte –> word.

CY3295 Kit Image

 

Finally modify the trcStreamingPort.c – AKA the PSoC DMA Streamport file.  Specifically you need to fix up the PSoC_Transmit to send out the data when the TraceRecorder buffer is full.

  • If the DMA is busy… then wait until the previous transaction is done.
  • Then setup the DMA and let it rip.

int32_t PSoC_Transmit(void* data, uint32_t size, int32_t *numOfBytesSent )
{
    
    while( CyDmaGetActiveChannels()& DMA_CHANNEL_MASK);
    DMA_SetSrcAddress(0, (void *)data);
    DMA_SetNumDataElements(0,size);
    DMA_ValidateDescriptor(0);
    DMA_ChEnable();
 
    *numOfBytesSent=size;
    
    return 0; // Doesnt matter what you return... i dont think that it is checked
}

The only other thing that needs to happen is configure the DMA in main.c

CyDmaEnable();
DMA_Init();
DMA_SetDstAddress(0, (void *)UART_TX_FIFO_WR_PTR);

Testing the PSoC DMA Streamport

Now when I startup the Tracealyzer, here is what I get:

CY3295 Kit Image

It looks like I solved my problem because that is way way better than:

CY3295 Kit Image

As always you can find all of these projects on the IotExpert GitHub site or git@github.com:iotexpert/PSoC-Tracelyzer.git

 

Blog: 

Comments

swinkemily3_2730976's picture

Appreciate your posts!best paper writing service reviews Thank you!

Hastaria Ayu's picture

We love to see that. Thank you. @ pulau tidung.

inwiperli1982_2979571's picture

I try, I really try. But since school I'm a complete dummy in everything related to science, especially electricity. Fortunately I had enough discounts at Freshessays.com from http://ratedbystudents.com/services/freshessays to have satisfactory grades. You see, I missed the basics somewhere. When I was a kid there was a cartoon on tv explaining electric current as a row of tiny men running inside the cable. When I came to school, I subconsciously tried to apply that image to what I was told.

leeam.ghazi_3168911's picture

The steam platform is used to distribute and spread games online. On steam store, you can download games. free steam gift codes

baraujo821_3211036's picture

Now you just have to improve your narrative essay writing skill and all gonna be alright!

本网站上的所有内容和材料均“按原样”提供。赛普拉斯半导体公司及其各个供应商对这些材料用于任何用途的适用性不作陈述,并且对关于这些材料的所有担保和条件概不负责,包括但不限于有关适销性、针对特定用途之适用性、权利和不侵犯任何第三方知识产权的所有暗示担保和条件。赛普拉斯半导体公司不授予任何明示或暗示的许可(无论是以默许方式或是任何其他方式)。使用本网站上的信息可能需要第三方的许可,或赛普拉斯半导体公司的许可。

本网站上的内容可能包含或必须遵守关于使用的特定准则或限制。所有帖子和使用本网站上的内容都必须遵守本网站的条款与条件;使用这些内容的第三方必须同意遵守任何限制或准则,并遵守本网站的条款与条件。赛普拉斯半导体公司及其供应商保留随时对内容和材料、产品、计划和服务进行纠正、删除、修改、增强、改进或其他变更,或者移动或终止任何内容、产品、计划或服务的权利,恕不另行通知。