You are here

TFT Display Shield Board CY8CKIT-028-TFT | 赛普拉斯半导体

TFT Display Shield Board CY8CKIT-028-TFT

最近更新: 
2020 年 4 月 21 日

TFT Display, Audio, and Multiple Sensors

The TFT Display Shield Board (CY8CKIT-028-TFT) has been designed such that a TFT display, audio devices, and sensors can interface with Cypress' PSoC 6 MCUs.

It comes with the features below to enable everyday objects to connect to the Internet of Things (IoT).

  • 2.4 inch TFT Display
  • Motion Sensor
  • Ambient Light Sensor
  • PDM Microphone
  • Audio Codec
  • 3.5-mm Audio Jack

This shield has a Newhaven 2.4″ 240×320 TFT display with a Sitronix ST7789 display controller and uses the 8080-Series Parallel Interface.

The TFT Display Shield Board is compatible with the PSoC 6 WiFi-BT Pioneer Kit CY8CKIT-062-WiFi-BT and the PSoC 6 BLE Pioneer Kit CY8CKIT-062-BLE. Refer to the respective kit guides for more details.



The table below shows the pin mapping for the PSoC 6 MCU Pioneer Kits that the TFT Display Shield is compatible with:

PCB Connector Pin Number Arduino Pin Arduino Function CY8CKIT-028-TFT Shield Function CY8CKIT-062-BLE

CY8CKIT-062-WiFi-BT
J1.1 VIN VIN 北卡罗来纳州 VIN
J1.2 GND GND GND GND
J1.3 GND GND GND GND
J1.4 5 V 5 V 北卡罗来纳州 5 V
J1.5 3.3 V 3.3 V VCC 3.3V 3.3 V
J1.6 RESET RESET 北卡罗来纳州 SWD RESET
J1.7 I/O REF I/O REF VIO REF P6 VDD
J1.8 -- -- 北卡罗来纳州 北卡罗来纳州
J2.1 A0 ADC0 ALS OUT P10[0]
J2.2 -- -- TFT DISP DB8 P9[0]
J2.3 A1 ADC1 Codec PDN SW P10[1]
J2.4 -- -- TFT DISP DB9 P9[1]
J2.5 A2 ADC2 IMU INT1 P10[2]
J2.6 -- -- TFT DISP DB10 P9[2]
J2.7 A3 ADC3 IMU INT2 P10[3]
J2.8 -- -- 北卡罗来纳州 P9[3]
J2.9 A4 ADC4 / SDA (I2C) PDM CLK P10[4]
J2.10 -- -- TFT DISP DB11 P9[4]
J2.11 A5 ADC5 PDM DATA P10[5]
J2.12 -- -- TFT DISP DB12 P9[5]
J3.1 D8 DIGITAL I/O TFT DISP DB14 P13[0]
J3.2 D9 PWM TFT DISP DB15 P13[1]
J3.3 D10 SS/PWM TFT DISP RD_L P12[3]
J3.4 D11 MOSI/PWM TFT DISP WR_L P12[0]
J3.5 D12 MISO TFT DISP D/C P12[1]
J3.6 D13 SCK TFT DISP RST_L P12[2]
J3.7 GND GND GND GND
J3.8 AREF analog ref i/p 北卡罗来纳州 VREF
J3.9 SDA SDA I2C SDA (IMU and audio codec) P6[1]
J3.10 SCL SCL I2C SCL (IMU and audio codec) P6[0]
J4.1 D0 RX I2S MCLK P5[0]
J4.2 D1 TX I2S TX SCK P5[1]
J4.3 D2 DIGITAL I/O I2S TX WS P5[2]
J4.4 D3 PWM, I/O I2S TX SDO P5[3]
J4.5 D4 DIGITAL I/O I2S RX SCK P5[4]
J4.6 D5 PWM, I/O I2S RX WS P5[5]
J4.7 D6 PWM, I/O I2S RX SDI P5[6]
J4.8 D7 DIGITAL I/O TFT DISP DB13 P0[2]

 

Code Examples in PSoC Creator and WICED Studio for the TFT Display Shield Board (CY8CKIT-028-TFT).

Project Development Platform Description
CE222221_TFT_VoiceRecorder CY8CKIT-062-WiFi-BT kit with PSoC Creator 4.2 software This code example shows how PSoC 6 MCU can be used to record audio data, store it, and play it back. It uses a digital microphone with the PDM/PCM hardware block. All the audio data captured by the microphone is stored in an external flash memory. After the recording is completed, you can play the audio data over I2S, which interfaces with an audio codec. You can record/play/ pause/resume with CapSense buttons. You control the audio volume with a CapSense slider. The TFT LCD displays the current state of the voice recorder, the volume, and the time of the record/play.
CE222494_WiFi_BT_WICED_WiFi_Demo CY8CKIT-062-WiFi-BT kit with WICED 6.1 software This code example demonstrates how to use PSoC 6 MCU and WICED to enable WiFi communication. It demonstrates how the PSoC 6 MCU with the 4343W module can be used as a configuration access point (AP) to allow a user to enter the credentials of their personal network.

To find out more on the CY8CKIT-062-WiFi-BT hardware, PSoC Creator 4.2, and WICED Studio 6.1, download the CY8CKIT-062-WiFi-BT Kit Guide from here.

To find standalone PSoC 6 MCU code examples for the CY8CKIT-062-WiFi-BT Pioneer Kit, you can also visit the PSoC 6 Code Examples page.

 
Kit Contents:
TFT Display Shield