FM4 S6E2G-Series Connectivity Arm® Cortex®-M4 Microcontroller (MCU) Family | 赛普拉斯半导体
FM4 S6E2G-Series Connectivity Arm® Cortex®-M4 Microcontroller (MCU) Family
S6E2G-Series are highly-integrated 32-bit microcontrollers with high performance and competitive cost. This series is based on the Arm Cortex-M4F processor with on-chip flash memory and SRAM. The portfolio includes high end communication modules such as IEEE 1588 compliant Ethernet, CAN, a hardware-based cryptographic assist module, serial communication interfaces (USB, UART, CSIO (SPI), I2C, LIN) and advanced control peripherals such as motor control timers, A/D converters, and a quadrature position/revolution counter.
S6E2G Series Highlights
High-Performance MCU Subsystem
- 608 CoreMark®, 180-MHz Arm® Cortex®-M4 CPU
- 244-µA/MHz active current with 2.7-V to 5.5-V operating voltage
- Up to 1MB flash and 192KB SRAM with a 16KB flash accelerator
- Error-Correcting Code (ECC) support, hardware watchdog timer (WDT), low-voltage detect, and clock supervisor blocks for safety-critical applications
- Independent power domains
数字子系统
- 2x Multi-Function Timers (MFT)
- 6x Programmable Pulse Generators (PPG)
- 16x Base Timers, 2x Quadrature Position/Revolution Counters (QPRC)
- 1x Dual Timer, 1x Cyclical Redundancy Check (CRC), and 1x Watch Counter
- 10x channels of Multi-Function Serial (MFS) interfaces configurable as SPI, UART, I2C, or LIN
- 2x USB, 1x CAN, IEEE 1588 Ethernet, 1x SD Card Interface, 2x Smart Card Interfaces, I2S and External Bus Interfaces
- Built-in Cryptographic Assist hardware coprocessor for encryption
Analog Subsystem
- 3x 12-bit, 2-Msps ADC with an up to 32-channel multiplexer input
S6E2GM-Series Block Diagram
1. 看门狗定时器 |
2. Cyclical Redundancy Check |
3. Controller Area Network |
4. Ethernet Communications with IEEE 1588 Precision Time Protocol (PTP) Standard |
5. Inter-IC Sound |
6. Memory Protection Unit |
7. Direct Memory Access |
8. Descriptor System Transfer Controller |
Function Differences between each S6E2G-Series by part
Series | S6E2GM | S6E2GK | S6E2GH | S6E2G3 | S6E2G2 |
USB 2.0 | 2 ch. | 2 ch. | 2 ch. | 2 ch. | 2 ch. |
CAN | 1 ch. | - | 1 ch. | - | - |
Ether-MAC |
1 ch. (Max) MII: 1 ch/ RMII: 1 ch (Max) |
1 ch. (Max) MII: 1 ch/ RMII: 1 ch (Max) |
- | - |
1 ch. (Max) MII: 1 ch/ RMII: 1 ch (Max) |
SD Card Interface | 1 unit | 1 unit | 1 unit | - | - |
- Watch the Introduction to the FM4 Portfolio video
- Download the S6E2G-Series Datasheet
- Purchase the FM4 Starter Kit (FM4-176L-S6E2GM) to evaluate the S6E2G-Series and start development
- Download the FM4 Peripheral Driver Library Software
- Start your first FM4 designs
- Join the Cypress Developer Community
FM4 S6E2G-Series Datasheets
|
FM4 S6E2G-Series Flash Specifications
|
FM4 S6E2G-Series Technical Reference Manual
|
应用手册
|
Peripheral Driver Library
FM MCU Peripheral Driver Library (PDL)
The FM MCU Peripheral Driver Library (PDL) simplifies software development for the FM0+, FM3, and FM4 MCU families. The PDL reduces the need to understand register usage and bit structures, thus easing software development for the extensive set of peripherals in the FM families. You configure the library for the particular device, and then use API calls to initialize and use a peripheral. Using the PDL makes it easier to port code from one family to the other, because the same code supports all FM families.
Support Tools
Vendor | Link | Comments |
IAR Systems | https://www.iar.com/iar-embedded-workbench/#!?architecture=ARM | IAR Embedded Workbench for Arm 7.50.2 or later |
Arm Keil | https://www.keil.com/download/product/ | Keil Embedded Development Tools for Arm 5.17 or later |
GCC Arm Embedded | https://launchpad.net/gcc-arm-embedded | GCC Arm Embedded 4.9-2015-q1-update or later |
iSystem | https://www.isystem.com/download/winidea/release-policy | iSYSTEM winIDEA 9.12 or later |
工具
Click on the link below to download the tool
Product | Description |
Pin and Code Wizard | Tool that helps set the IO ports for Cypress's 32-bit Arm Cortex FM MCUs |
Serial Port Viewer Tool | Tool that is used to monitor all available com ports and provides a terminal emulator |
CMSIS-DAP USB Drivers | CMSIS-DAP is the interface firmware for a Debug Unit that connects the Debug Port to USB. Debuggers, which execute on a host computer, connect via USB to the Debug Unit and to the Device that runs the application software |
FLASH Programmer | Tool that converts RS232C data to readable data on your PC |
USB Wizard | Tools that supports editing USB descriptors and templates |
FM4 MCU Starter Kits
These kits will help you get started with FM4 MCU development.
|
The Sample Programs ("Programs") are offered for use in developing systems for Cypress microcontrollers.
The Programs will be useful in the following situations:
- I need a simple sample program, as I am going to develop software. The sequence of resource access, among others, can be confirmed using these Programs.
- I would like to examine, before development, whether each resource will operate as expected.
The Programs support several specifications, even for the operation of one resource. - If resources do not operate properly on my system, I would like software for which confirmation of operation has been completed. Cypress has confirmed the actual operation of the Programs on each of its microcontrollers, so you will be able to compare your program with the Program.
For the FM portfolios, code examples are provided with the Peripheral Driver Library (PDL). Download and install the PDL, and look in the examples folder.